ANUAL SERVICE M

TAIL LIGHT

INSPECTION

Start the engine and check the tail light illumination.

TAIL LIGHT

If any LED does not turn on, replace the tail light unit.

CLAMPS STAY

CONNECTORS

TAIL LIGHT

SCREWS

TAIL LIGHT UNIT

REMOVAL/INSTALLATION

Remove the following:

- Seat (page 3-3)

- Side covers (page 3-3)

Disconnect the tail light wire connectors. Remove the screws and wire clamps.

Remove the screws, stay and tail light unit.

Installation is in the reverse order of removal.

TORQUE:

Tail light mounting screw:

4.2 N m (0.4 kgf-m, 3.1 lbf-ft)

Tail light wire clamp screw:

0.7 N m (0.1 kgf-m, 0.5 lbf-ft)

ENGINE STOP BUTTON

TAIL LIGHT

3P (BLACK) CONNECTOR

INSPECTION

Remove the front visor.

- '05-'07: (page 3-5)

- After '07: (page 3-6)

TAIL LIGHT

(BLACK) CONNECTOR '05 - '07 shown: ^ ENGINE STOP BUTTON

TAIL LIGHT

Check for continuity between the Black/white termi­nal and Black/green terminal.

There should be continuity with the engine stop but­ton depressed, and no continuity with the button released.

Disconnect the engine stop button 3P (Black) con­nector.

CLUTCH SWITCH

INSPECTION

'05 - '07:

TAIL LIGHT

Remove the front visor.

- '05-'07: (page 3-5)

- After '07: (page 3-6)

Disconnect the engine stop button 3P (Black) con­nector and clutch switch wire (Black/red) connector.

Check for continuity between the Black/brown ter­minal and Black/red wire connector.

There should be continuity with the clutch lever squeezed, and no continuity with the clutch lever released.

If the continuity is abnormal, remove the clutch switch (page 20-8).

TAIL LIGHT

REMOVAL/INSTALLATION

Remove the boot.

SCREW

CONNECTORS

TAIL LIGHT

Remove the screw, stay, clutch switch and discon - CLUTCH^MTCH nect the connectors.

Check for continuity between the clutch switch ter­minals.

CLUTCH SWITCH

TAIL LIGHT

There should be no continuity with the switch pushed, and there should be continuity with the switch is released.

If the continuity at the connectors is abnormal and the continuity at the clutch switch terminal is nor­mal, check the connectors for loose connection and the wire harness for an open circuit or loose con­nection.

ANUAL SERVICE M

TROUBLESHOOTING

ENGINE DOES NOT START OR IS HARD TO START 1. Fuel Line Inspection Check fuel flow to carburetor. Does fuel reach the carburetor? IMO - • Clogged fuel hose or …

WIRING DIAGRAM

WIRING DIAGRAM WIRING DIAGRAM

STARTER SWITCH

INSPECTION '05 - '07: Remove the front visor. - '05 -'07: (page 3-5) - After '07: (page 3-6) Disconnect the starter switch 2P (Black) connector. STARTER SWITCH Check for continuity …

Как с нами связаться:

Украина:
г.Александрия
тел./факс +38 05235  77193 Бухгалтерия

+38 050 457 13 30 — Рашид - продажи новинок
e-mail: msd@msd.com.ua
Схема проезда к производственному офису:
Схема проезда к МСД

Партнеры МСД

Контакты для заказов оборудования:

Внимание! На этом сайте большинство материалов - техническая литература в помощь предпринимателю. Так же большинство производственного оборудования сегодня не актуально. Уточнить можно по почте: Эл. почта: msd@msd.com.ua

+38 050 512 1194 Александр
- телефон для консультаций и заказов спец.оборудования, дробилок, уловителей, дражираторов, гереторных насосов и инженерных решений.